What's Wrong with My Puffco Peak? Step 6: Open and Inspect. I still have some detective work to do to determine why my Puffco Peak doesn't charge. Place your fingers above the USB port where the shiny material and silicone meet and pry upwards on the shiny metal/plastic piece that surrounds the Puffco Peak. In my case – I did some poking around with a multimeter and determined that my battery was not putting out a high enough voltage. If you have done this before it makes sense, otherwise: read on. Remove all three screws, and your Puffco will almost fall apart in your hands.
- Puffco peak short circuit fix spray
- Puffco peak short circuit fix light
- Puffco peak not working
- Puffco peak knock off
- Puffco peak short circuit fix n
- Puffco peak short circuit fixe
Puffco Peak Short Circuit Fix Spray
Be careful and go slow. We're starting off with a standard Puffco Peak base – glass removed. Step 4: Pry the Metal Base Off. That's it, your Puffco Peak is open before you.
Puffco Peak Short Circuit Fix Light
I was told, "It doesn't charge – it's broken. 4v battery pack – unless there were a buck converter somewhere on the battery pack I have yet to find. One of these screws is below a security sticker, revealing silver 'VOID' markings when removed. The adhesive is fairly strong, and so some force is required to remove this piece. Using your thumbs, press outwards from the center on the base of the Puffco Peak. If that isn't the case, I'll be adding an external battery pack to make up for the lack of internal charge circuit. Use your fingers or a pry tool to peel the metal disc off of the bottom of the plastic Puffco Peak base. When removed however, the battery is completely dead and the Puffco shows no signs of life. My puffco wont heat up, instead it blinks 5 times, on whichever heat setting i have it on. This can be removed as one whole piece, or disassembled and removed piece by piece. Use a screwdriver set like this one from Amazon to remove the three screws holding the plastic assembly together. It's only on USB power that the device fails to charge. Checking the voltage supplied to the battery while plugged into USB showed only 4.
Puffco Peak Not Working
The teardown video is up on Youtube now: Step by Step Instructions: How to Open a Puffco Peak. It may help to warm this area with a hair dryer or gently using a heat gun. Ideally, finding out which component has failed; and swapping it for a working one is best – but my electronics skills are limited. Lift the entire component out of the silicone well.
Puffco Peak Knock Off
It will lift off, and may require a twisting motion or a small amount of heat if it feels stuck. The bucket rests directly atop the heating element – extract can glue it in place – and tugging on the element can damage it's fragile connecting wires. Note: In my video, I perform step 5 before step 4 – and it really doesn't matter in the end, but I feel it's easier in this order. I suspect that there is an onboard boost converter that steps USB voltage up to above 7v, and it is defective. This faulty Puffco Peak vaporizer came into my possession within the last few weeks, via a friend of mine. Do not force this out. Once the silicone boot is loose the the bottom, pry upwards from below the USB port and remove the silicone sort of like a sock, where the atomizer connection is the toe.
Puffco Peak Short Circuit Fix N
Step 3: Remove the Silicone Boot. This is the most confusing part of this disassembly, and I suggest you watch the video starting from about the 1:00 minute mark for a video example. If anyone has input, questions or ideas – I would love to hear them in the comments below or on the Youtube video linked above. Next steps are to poke around a bit more, and see if rescuing this battery back above it's rated voltage is enough to keep it working. I just needed to get inside and start probing around with my multimeter. Step 2: Pry the Shiny Metal Piece Upwards. Let's assume you don't need a hand in figuring out how to remove the glass from your puffco.
Puffco Peak Short Circuit Fixe
Step 5: Unscrew 3 Security Screws. Begin the disassembly process by removing the atomizer, bucket, and surrounding components. These devices are simple, and with that in mind; there shouldn't be too many ways for the device to fail. I assume that this is the case, because when I apply 7. The silicone will lift out from under the shiny metal base of the Puffco. If it feels stuck, apply a small amount of heat and try again.
Unscrew the metal housing for the heater by turning it counter clockwise several times to disengage the threads. It should lift right out. 5v to the battery connection leads – the battery charges and holds its charge. You may use a guitar pick or some other soft plastic prying tool to start the job if your fingers can't get in there.